mirror of
https://github.com/vyos/vyos-documentation.git
synced 2025-10-26 08:41:46 +01:00
76 lines
2.4 KiB
ReStructuredText
76 lines
2.4 KiB
ReStructuredText
.. _bond-interface:
|
|
|
|
Bond
|
|
----
|
|
|
|
You can combine (aggregate) 2 or more physical interfaces into a single
|
|
logical one. It's called bonding, or LAG, or ether-channel, or port-channel.
|
|
|
|
Create interface bondX, where X is just a number:
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces bonding bond0 description 'my-sw1 int 23 and 24'
|
|
|
|
You are able to choose a hash policy:
|
|
|
|
.. code-block:: none
|
|
|
|
vyos@vyos# set interfaces bonding bond0 hash-policy
|
|
Possible completions:
|
|
layer2 use MAC addresses to generate the hash (802.3ad)
|
|
layer2+3 combine MAC address and IP address to make hash
|
|
layer3+4 combine IP address and port to make hash
|
|
|
|
For example:
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces bonding bond0 hash-policy 'layer2'
|
|
|
|
You may want to set IEEE 802.3ad Dynamic link aggregation (802.3ad) AKA LACP
|
|
(don't forget to setup it on the other end of these links):
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces bonding bond0 mode '802.3ad'
|
|
|
|
or some other modes:
|
|
|
|
.. code-block:: none
|
|
|
|
vyos@vyos# set interfaces bonding bond0 mode
|
|
Possible completions:
|
|
802.3ad IEEE 802.3ad Dynamic link aggregation (Default)
|
|
active-backup
|
|
Fault tolerant: only one slave in the bond is active
|
|
broadcast Fault tolerant: transmits everything on all slave interfaces
|
|
round-robin Load balance: transmit packets in sequential order
|
|
transmit-load-balance
|
|
Load balance: adapts based on transmit load and speed
|
|
adaptive-load-balance
|
|
Load balance: adapts based on transmit and receive plus ARP
|
|
xor-hash Load balance: distribute based on MAC address
|
|
|
|
Now bond some physical interfaces into bond0:
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces bonding bond0 member interface eth0
|
|
set interfaces bonding bond0 member interface eth1
|
|
|
|
After a commit you may treat bond0 as almost a physical interface (you can't
|
|
change its` duplex, for example) and assign IPs or VIFs on it.
|
|
|
|
You may check the result:
|
|
|
|
.. code-block:: none
|
|
|
|
vyos@vyos# run sh interfaces bonding
|
|
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
|
|
Interface IP Address S/L Description
|
|
--------- ---------- --- -----------
|
|
bond0 - u/u my-sw1 int 23 and 24
|
|
bond0.10 192.168.0.1/24 u/u office-net
|
|
bond0.100 10.10.10.1/24 u/u management-net
|