mirror of
https://github.com/vyos/vyos-documentation.git
synced 2025-11-04 00:02:05 +01:00
142 lines
4.7 KiB
ReStructuredText
142 lines
4.7 KiB
ReStructuredText
.. include:: ../_include/need_improvement.txt
|
|
|
|
.. _routing-ospf:
|
|
|
|
####
|
|
OSPF
|
|
####
|
|
|
|
:abbr:`OSPF (Open Shortest Path First)` is a routing protocol for Internet
|
|
Protocol (IP) networks. It uses a link state routing (LSR) algorithm and falls
|
|
into the group of interior gateway protocols (IGPs), operating within a single
|
|
autonomous system (AS). It is defined as OSPF Version 2 in :rfc:`2328` (1998)
|
|
for IPv4. Updates for IPv6 are specified as OSPF Version 3 in :rfc:`5340`
|
|
(2008). OSPF supports the :abbr:`CIDR (Classless Inter-Domain Routing)`
|
|
addressing model.
|
|
|
|
OSPF is a widely used IGP in large enterprise networks.
|
|
|
|
OSPFv2 (IPv4)
|
|
#############
|
|
|
|
In order to have a VyOS system exchanging routes with OSPF neighbors, you will
|
|
at least need to configure an OSPF area and some network.
|
|
|
|
.. code-block:: none
|
|
|
|
set protocols ospf area 0 network 192.168.0.0/24
|
|
|
|
That is the minimum configuration you will need.
|
|
It is a good practice to define the router ID too.
|
|
|
|
.. code-block:: none
|
|
|
|
set protocols ospf parameters router-id 10.1.1.1
|
|
|
|
|
|
Below you can see a typical configuration using 2 nodes, redistribute loopback
|
|
address and the node 1 sending the default route:
|
|
|
|
**Node 1**
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces loopback lo address 10.1.1.1/32
|
|
set protocols ospf area 0 network 192.168.0.0/24
|
|
set protocols ospf default-information originate always
|
|
set protocols ospf default-information originate metric 10
|
|
set protocols ospf default-information originate metric-type 2
|
|
set protocols ospf log-adjacency-changes
|
|
set protocols ospf parameters router-id 10.1.1.1
|
|
set protocols ospf redistribute connected metric-type 2
|
|
set protocols ospf redistribute connected route-map CONNECT
|
|
|
|
set policy route-map CONNECT rule 10 action permit
|
|
set policy route-map CONNECT rule 10 match interface lo
|
|
|
|
**Node 2**
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces loopback lo address 10.2.2.2/32
|
|
set protocols ospf area 0 network 192.168.0.0/24
|
|
set protocols ospf log-adjacency-changes
|
|
set protocols ospf parameters router-id 10.2.2.2
|
|
set protocols ospf redistribute connected metric-type 2
|
|
set protocols ospf redistribute connected route-map CONNECT
|
|
|
|
set policy route-map CONNECT rule 10 action permit
|
|
set policy route-map CONNECT rule 10 match interface lo
|
|
|
|
OSPFv3 (IPv6)
|
|
#############
|
|
|
|
A typical configuration using 2 nodes.
|
|
|
|
**Node 1:**
|
|
|
|
.. code-block:: none
|
|
|
|
set protocols ospfv3 area 0.0.0.0 interface eth1
|
|
set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64
|
|
set protocols ospfv3 parameters router-id 192.168.1.1
|
|
set protocols ospfv3 redistribute connected
|
|
|
|
**Node 2:**
|
|
|
|
.. code-block:: none
|
|
|
|
set protocols ospfv3 area 0.0.0.0 interface eth1
|
|
set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64
|
|
set protocols ospfv3 parameters router-id 192.168.2.1
|
|
set protocols ospfv3 redistribute connected
|
|
|
|
.. note:: You can not easily redistribute IPv6 routes via OSPFv3 on a WireGuard
|
|
interface link. This requires you to configure link-local addresses manually
|
|
on the WireGuard interfaces, see :vytask:`T1483`.
|
|
|
|
Example configuration for WireGuard interfaces:
|
|
|
|
**Node 1**
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces wireguard wg01 address 'fe80::216:3eff:fe51:fd8c/64'
|
|
set interfaces wireguard wg01 address '192.168.0.1/24'
|
|
set interfaces wireguard wg01 peer ospf02 allowed-ips '::/0'
|
|
set interfaces wireguard wg01 peer ospf02 allowed-ips '0.0.0.0/0'
|
|
set interfaces wireguard wg01 peer ospf02 endpoint '10.1.1.101:12345'
|
|
set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...='
|
|
set interfaces wireguard wg01 port '12345'
|
|
set protocols ospfv3 parameters router-id 192.168.1.1
|
|
set protocols ospfv3 area 0.0.0.0 interface 'wg01'
|
|
set protocols ospfv3 area 0.0.0.0 interface 'lo'
|
|
|
|
**Node 2**
|
|
|
|
.. code-block:: none
|
|
|
|
set interfaces wireguard wg01 address 'fe80::216:3eff:fe0a:7ada/64'
|
|
set interfaces wireguard wg01 address '192.168.0.2/24'
|
|
set interfaces wireguard wg01 peer ospf01 allowed-ips '::/0'
|
|
set interfaces wireguard wg01 peer ospf01 allowed-ips '0.0.0.0/0'
|
|
set interfaces wireguard wg01 peer ospf01 endpoint '10.1.1.100:12345'
|
|
set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...='
|
|
set interfaces wireguard wg01 port '12345'
|
|
set protocols ospfv3 parameters router-id 192.168.1.2
|
|
set protocols ospfv3 area 0.0.0.0 interface 'wg01'
|
|
set protocols ospfv3 area 0.0.0.0 interface 'lo'
|
|
|
|
**Status**
|
|
|
|
.. code-block:: none
|
|
|
|
vyos@ospf01:~$ sh ipv6 ospfv3 neighbor
|
|
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
|
|
192.168.0.2 1 00:00:37 Full/PointToPoint 00:18:03 wg01[PointToPoint]
|
|
|
|
vyos@ospf02# run sh ipv6 ospfv3 neighbor
|
|
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
|
|
192.168.0.1 1 00:00:39 Full/PointToPoint 00:19:44 wg01[PointToPoint]
|
|
|