mirror of
https://github.com/vyos/vyos-documentation.git
synced 2025-11-04 00:02:05 +01:00
76 lines
2.6 KiB
ReStructuredText
76 lines
2.6 KiB
ReStructuredText
.. _loopback-interface:
|
|
|
|
########
|
|
Loopback
|
|
########
|
|
|
|
The loopback networking interface is a virtual network device implemented
|
|
entirely in software. All traffic sent to it "loops back" and just targets
|
|
services on your local machine.
|
|
|
|
.. note:: There can only be one loopback ``lo`` interface on the system. If
|
|
you need multiple interfaces, please use the :ref:`dummy-interface`
|
|
interface type.
|
|
|
|
.. hint:: A lookback interface is always up, thus it could be used for
|
|
management traffic or as source/destination for and :abbr:`IGP (Interior
|
|
Gateway Protocol)` like :ref:`bgp` so your internal BGP link is not dependent
|
|
on physical link states and multiple routes can be chosen to the
|
|
destination. A :ref:`dummy-interface` Interface should always be preferred
|
|
over a :ref:`loopback-interface` interface.
|
|
|
|
Configuration
|
|
=============
|
|
|
|
Address
|
|
-------
|
|
|
|
.. cfgcmd:: set interfaces loopback lo address <address>
|
|
|
|
Configure Loopback interface `lo` with one or more interface addresses.
|
|
Address can be specified multiple times as IPv4 and/or IPv6 address, e.g.
|
|
192.0.2.1/24 and/or 2001:db8::1/64.
|
|
|
|
Link Administration
|
|
-------------------
|
|
|
|
.. cfgcmd:: set interfaces loopback lo description <description>
|
|
|
|
Assign given `<description>` to interface `lo`. Description will also be
|
|
passed to SNMP monitoring systems.
|
|
|
|
Operation
|
|
=========
|
|
|
|
.. opcmd:: show interfaces loopback
|
|
|
|
Show brief interface information.
|
|
|
|
.. code-block:: none
|
|
|
|
vyos@vyos:~$ show interfaces loopback
|
|
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
|
|
Interface IP Address S/L Description
|
|
--------- ---------- --- -----------
|
|
lo 127.0.0.1/8 u/u
|
|
::1/128
|
|
|
|
.. opcmd:: show interfaces loopback lo
|
|
|
|
Show detailed information on given loopback interface `lo`.
|
|
|
|
.. code-block:: none
|
|
|
|
vyos@vyos:~$ show interfaces ethernet eth0
|
|
lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
|
|
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
|
|
inet 127.0.0.1/8 scope host lo
|
|
valid_lft forever preferred_lft forever
|
|
inet6 ::1/128 scope host
|
|
valid_lft forever preferred_lft forever
|
|
|
|
RX: bytes packets errors dropped overrun mcast
|
|
300 6 0 0 0 0
|
|
TX: bytes packets errors dropped carrier collisions
|
|
300 6 0 0 0 0
|